Дом >
Новости
> Новости компании о Модель

Модель

2026-11-18

Последние новости компании о Модель
Pressure Gauge Model Selection System
Pressure Gauge Configurator

Select by parameter,
Real-time generation of model codes and specifications

Covers Y25 to Y160, a total of 10 shell diameters. Select installation direction, shell and connector material, accuracy, scale and thread. The system automatically assembles the model code according to the naming rules, and simultaneously outputs the pressure unit conversion result.

10 specifications 15 parameter dimensions 3 optional units 11 pressure unit conversions
01

Parameter Model

Options move with the specification, inconsistent parameters will be grayed out and the reason will be marked
AShell Diameter / SpecificationDetermine the applicable parameter range
BConnection DirectionRadial / Axial / With edge
CType and ShockproofDry type and oil-filled shockproof are mutually exclusive
Shockproof oil
DShell and Connector MaterialCopper / Iron / Stainless steel
Shell material
Connector material
EAccuracy LevelThe smaller the value, the higher the accuracy
FScale and UnitThe scale in the table is marked in bar
Dial unit
Actual working pressure (filled in according to dial unit)
Not filled
GConnector ThreadChanges with specification
HCustom RequirementsFull specification support
Custom scale / brand
Custom LOGO
Additional requirements (self-input)0 / 10
Configured model
—
—
bar —
    02

    Pressure Unit Conversion

    Pressure conversion, 1 bar = 100 kPa = 14.5038 psi
    Input value
    Source unit
    Common presets

    Convert according to international unit standards and engineering definitions (1 psi = 6894.757 Pa, 1 kgf/cm² = 98066.5 Pa, 1 mmHg = 133.3224 Pa, 1 inH₂O = 249.0889 Pa).

    Three easily confused interfaces

    Gauge pressureTaking atmospheric pressure as zero, all pressure gauge readings are gauge pressure;Absolute pressureTaking absolute vacuum as zero, absolute pressure ≈ gauge pressure + 101.325 kPa.

    Dual scale: Inner circle bar, outer circle psi is a common practice. The "Scale" on this page also provides conversions for MPa / psi, which can be directly compared with the quotation and drawings.

    kgf/cm²differs from bar by about 2%, these are two different units, not different ways of writing the same scale.

    Values are all calculated from source values, no human rounding is done; engineering quotations and scale markings usually take 3-4 significant digits.

    Unit Conversion Table1 unit = the following value
    Unit Pa kPa MPa bar psi kgf/cm²

    The bold "1" indicates that the unit in this row is itself. Water column units are calculated based on 4°C pure water density, and mercury columns are calculated based on 0°C mercury density, consistent with industry common practices for instrument rows.

    03

    Factory common scale cross-reference

    Automatically converted from the scale sequence in the model parameter table
    Scale (bar) MPa psi kgf/cm² kPa Applicable specifications

    "Applicable specifications" automatically matches each specification scale sequence in the table; the scale system of Y25 and Y30 is obviously smaller than medium and large specifications, and small specifications do not produce high-pressure scales. This table is for accurate conversion values, and the dial scale is marked according to the integer rule in Section 04.

    04

    Model Naming and Model Rules

    Automatically executed based on the notes in the parameter table

    Naming rules

    Letters are assembled in order, numbers are shell diameters, separated by "-" in between.

    YPressure Gauge (Fixed first position)
    NShockproof (Oil-filled shockproof)
    BStainless steel (shell)
    FAll steel (stainless steel connector)
    ZAxial direction
    TWith edge
    Example:YNBFZT-100→ Axial direction with edge, stainless steel shell all steel, oil-filled shockproof pressure gauge with a diameter of 100 mm

    Mutual restriction

    Dry type and oil-filled shockproof are mutually exclusive.When selecting dry type, oil or silicone oil cannot be selected; after selecting shockproof oil, dry type cannot be selected.

    Iron shell and oil-filled shockproof are mutually exclusive.Iron shell (coated iron shell) can only be dry type; oil-filled shockproof requires a stainless steel shell.

    Restrictions come from parameter table notes:
    "When selecting dry type and iron shell, shockproof oil cannot be selected. After selecting shockproof oil, dry type or iron shell cannot be selected."

    Scale verification

    General engineering practice: static pressure scale is 1/3 to 3/4, dynamic or impact pressure is reduced by one level.After filling in "Actual working pressure", this page will provide real-time scale utilization ratio and recommendations. Less than 30% indicates that the scale is too large and the reading accuracy is wasted; more than 75% poses a risk of overpressure.Recommended range 30% – 75%

    Dial value rounding

    When selecting bar, keep the value in the table; when selecting MPa, take 1/10 of the original value; when selecting psi, take 14.5 times the original value and round it, keeping at most three significant digits, and supplement with zeros at the end.

    Example: 15 bar → 1.5 MPa → 218 psi (15 × 14.5 = 217.5, rounded to 218 with three significant digits).

    When "Custom scale / brand" or "Custom LOGO" is selected as "Yes", additional requirements must be filled in with at least 10 characters, otherwise the model order cannot be duplicated.

    Anhui Xingyi Instrument Co., Ltd.

    Data source:

    (Sheet1, 10 model codes × 15 parameter columns, including 3 rows of notes).Interface description: Duplicate items in the original table "Scale (bar)" column (e.g., 50 appearing twice) have been removed; the original scale units for the Y25 row were numerical values 50100150200300400. This page restores them to 50 / 100 / 150 / 200 / 300 / 400. Please verify with the actual product catalog.This page is a model auxiliary tool. The final specifications, material part numbers, and prices should be confirmed with the official quotation and drawings; the page is an offline version of a single document, and the data has been embedded in the code and cannot be called online.