Evde >
Haberler
> Şirket haberleri hakkında Model

Model

2026-11-18

Son şirket haberleri Model
Pressure Gauge Selection System
Pressure Gauge Configurator

Select by parameter,
Real-time generation of model codes and specifications

Covers Y25 to Y160, a total of 10 case diameters. Select installation direction, case and connection material, accuracy, scale and thread end, system automatically assembles model code according to naming rules, and simultaneously outputs pressure unit conversion results.

10 specifications 15 parameter dimensions 3 selectable units 11 pressure unit conversions
01

Parameter selection

Options move with the specification, inconsistent parameters will be grayed out and the reason will be marked
ACase diameter / SpecificationDetermine the applicable parameter range
BConnection directionRadial / Axial / With edge
CType and shock resistanceDry type and oil-filled shock absorption mutually exclusive
Shockproof oil
DCase and connection materialCopper / Iron / Stainless steel
Case material
Connection material
EAccuracy levelThe smaller the value, the more accurate
FScale and unitScale in the table is marked in bar
Dial unit
Actual working pressure (filled in according to dial unit)
Not filled
GConnection threadChanges with specification
HCustom requirementsFull specification support
Custom scale / brand
Custom LOGO
Additional requirements (self-input)0 / 10
Configured model number
—
—
bar —
    02

    Pressure unit conversion

    Pressure conversion, 1 bar = 100 kPa = 14.5038 psi
    Input value
    Source unit
    Common presets

    Conversion according to international unit standards and common engineering definitions (1 psi = 6894.757 Pa, 1 kgf/cm² = 98066.5 Pa, 1 mmHg = 133.3224 Pa, 1 inH₂O = 249.0889 Pa).

    Three easily confused interfaces

    Gauge pressureTaking atmospheric pressure as zero, all pressure gauge readings are gauge pressure;Absolute pressureTaking absolute vacuum as zero, absolute pressure ≈ gauge pressure + 101.325 kPa.

    Dual scale: Inner circle bar, outer circle psi is a common practice, this page 'Scale' also outputs MPa / psi conversion, which can be directly referenced for quotation and drawings.

    kgf/cm²Approximately 2% difference with bar, these are two different units, not different ways of writing the same scale.

    Values are all calculated from source values, no human rounding is done; engineering quotation and scale markings usually take 3-4 significant digits.

    Unit conversion table1 unit = the following value
    Unit Pa kPa MPa bar psi kgf/cm²

    Bold '1' indicates that the unit in this row is itself. Water column units are converted according to 4°C pure water density, and mercury columns are converted according to 0°C mercury density, consistent with industry common practices for instrument rows.

    03

    Factory common scale cross-unit conversion table

    Taken from the scale sequence in the model parameter table, automatically converted
    Scale (bar) MPa psi kgf/cm² kPa Applicable specifications

    'Applicable specifications' automatically matches each specification scale sequence in the table; the scale system of Y25 and Y30 is significantly smaller than medium and large specifications, and small specifications do not produce high-pressure scales. This table is for accurate conversion values, and the dial scale is marked according to the integer rule in section 04.

    04

    Model naming and selection rules

    Automatically executed based on parameter table annotations

    Naming rules

    Letters are assembled in order, numbers are case diameters, separated by '-' in between.

    YPressure gauge (fixed first position)
    NShockproof (oil-filled)
    BStainless steel (case)
    FAll steel (connection stainless steel)
    ZAxial direction
    TWith edge
    Example:YNBFZT-100→ Axial direction with edge, stainless steel case, all steel, oil-filled shockproof pressure gauge with a diameter of 100 mm

    Mutual exclusion

    Dry type and oil-filled shock absorption are mutually exclusive.When selecting dry type, oil-filled or silicone oil cannot be selected; after selecting shockproof oil, dry type cannot be selected.

    Iron case and oil-filled shock absorption are mutually exclusive.Iron cases (coated iron cases) can only be dry type; oil-filled shock absorption requires stainless steel cases.

    Exclusions come from parameter table annotations:
    'Select dry type, iron cases cannot select shockproof oil; after selecting shockproof oil, dry type or iron cases cannot be selected'.

    Scale verification

    General engineering method: Static pressure is measured within 1/3 to 3/4 of the scale; dynamic or impulse pressure is reduced by one level.After filling in 'Actual working pressure', this page will display the scale utilization ratio and recommendations in real-time. Less than 30% indicates the scale is too large, wasting reading accuracy; greater than 75% poses an overpressure risk.Recommended range 30% – 75%

    Dial value rounding

    When selecting bar, maintain the value in the table; when selecting MPa, take 1/10 of the original value; when selecting psi, take 14.5 times the original value and round to the nearest integer, keeping at most three significant digits, and append zeros at the end.

    Example: 15 bar → 1.5 MPa → 218 psi (15 × 14.5 = 217.5, rounded to 218 after rounding to three significant digits).

    When 'Custom scale / brand' or 'Custom LOGO' is selected as 'Yes', additional requirements must be filled in with at least 10 characters, otherwise the selection form cannot be duplicated.

    Anhui Xingyi Instrument Co., Ltd.

    Data source:

    (Sheet1, 10 model numbers × 15 parameter columns, including 3 annotation rows).Interface description: Duplicate items in the original table's 'Scale (bar)' column (e.g., 50 appearing twice) have been removed; the scale units for the Y25 row were originally numerical values 50100150200300400. This page restores them to 50 / 100 / 150 / 200 / 300 / 400. Please verify with the actual product directory.This page is a model selection auxiliary tool. The final specifications, material part numbers, and prices are subject to confirmation with the official quotation sheet and drawings; the page is a single file offline version, and the data has been embedded in the code and does not require network access.